Cabinet door size calculator
Half overlay is smaller. Check your hinge spec sheet.
Each door
- Width × height
- 596 × 732 mm
- In inches (1/16)
- 23 7/16" × 28 13/16"
- Pieces
- 1
Overlay: the door covers the cabinet face. Inset: it sits inside the opening, flush.
Save this, optimize the cut list and quote it in Zeder Studio.
On this page (5)
Door size comes from the cabinet opening, not the outside of the box. This calculator applies the formulas for overlay and inset doors, single or pairs, and gives the result in millimeters and fractional inches.
How the calculation works
Overlay: height = opening + 2 × overlay
Inset: width = (opening − 2 × gap − center gap) ÷ doors
Inset: height = opening − 2 × gap
The center gap only applies to a pair. Overlay is how much the door covers the cabinet side on each edge; it’s set by the concealed (cup) hinge and the side thickness, so take it from your hinge spec sheet. The inset perimeter gap is the reveal between the door and the frame on each side. Inputs are in millimeters; use the converter for inch sizes.
Worked example
A 30" wall cabinet with a 28 1/2" × 30" opening (723.9 × 762 mm), a pair of doors, 1/2" overlay (12.7 mm) and a 1/8" center gap (3.175 mm):
Height: 30 + 2 × 1/2 = 31 in
In mm: (723.9 + 25.4 − 3.175) ÷ 2 = 373.06 × 787.4 mm
And with the calculator’s metric defaults (564 × 700 mm opening, 16 mm overlay, 2 mm gap, 3 mm between doors), which is a 600 mm base cabinet with 18 mm sides:
| Case | Each door (mm) | Inches (1/16) |
|---|---|---|
| Overlay, 1 door | 596 × 732 | 23 7/16 × 28 13/16 |
| Overlay, 2 doors | 296.5 × 732 | 11 11/16 × 28 13/16 |
| Inset, 1 door | 560 × 696 | 22 1/16 × 27 3/8 |
| Inset, 2 doors | 278.5 × 696 | 10 15/16 × 27 3/8 |
Overlay or inset: which to choose
Overlay doors are the default on frameless melamine cabinets: they cover the box edges, forgive small out-of-square errors and adjust with the hinge screws. Inset doors sit flush with the box and look more refined, but they need a square box, even reveals and more fitting time; any error shows in the gap around the door. When in doubt, start with overlay.
Drawer fronts use the same width formula. For height, split the opening between the drawers and subtract a gap between each front.
Common mistakes
- Measuring the outside of the box. The formula uses the clear opening between sides, bottom and top.
- Full overlay on a shared side. When two doors close on the same partition, each covers only part of it: that’s half overlay, with the matching hinge.
- Skipping the center gap on a pair. Without it the doors hit when they close.
- Not deducting banding. The calculator gives the finished size. With thick banding the cut size is smaller; in Zeder Studio that’s the Deduct edge band from cut size setting.
- Sideways grain. On woodgrain melamine, doors almost always run grain vertical: set them to Lengthwise in the cut list.
Tips
- Make a test door before cutting the whole set, especially after switching hinges.
- Typical cabinet heights and widths are in standard kitchen cabinet dimensions.
- If you design in the Design module, doors come from your shop’s construction rules and go to Cut with the rest of the parts (how design works).
- Working on kitchens or closets? See how Zeder Studio handles them end to end.
Related
Standard kitchen cabinet dimensions
Typical heights, depths and widths for base, wall and tall cabinets in the US and Mexico, with a dimensioned diagram and how they turn into parts.
mm to inches
Convert millimeters to fractional inches (1/16, 1/32, 1/64) and inches like 23 7/8 back to millimeters. Built for the shop.
Cabinet design
Design kitchens, closets and vanities cabinet by cabinet, review them in 3D and send the cut list straight to the optimizer. Nothing to install.
Cabinetmaking glossary
What melamine, MDF, edge banding, kerf, grain, offcut, cut list, panel saw, cup hinge, 32 mm system, toe kick and other shop terms mean.
Closet makers
Design closets and walk-ins, work out parts and edge band, optimize melamine, keep offcuts and send clear quotes the same day.
Edge banding types and how to calculate it
PVC, ABS, melamine and wood veneer banding: thicknesses, widths, when to use each and how to calculate meters per part and per kitchen.
Frequently asked questions
How do I calculate an overlay door size?
Width = opening + 2 × overlay; height = opening + 2 × overlay. For a pair, subtract the center gap and divide the width by two.
How much overlay should a cabinet door have?
It depends on the hinge and the side thickness. Take it from your hinge spec sheet; the calculator starts at 16 mm (about 5/8").
What gap should I leave on an inset door?
A couple of millimeters (around 1/16" to 3/32") per side is typical; the calculator starts at 2 mm. Adjust to your hinges and how square your boxes are.
Cut better starting with your next job
Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.