Standard kitchen cabinet dimensions: US vs. Mexico
- Type
- Guide
- Updated
- Reading time
- 8 min
- Sections
- 10
On this page (10)
- The key dimensions at a glance
- Base cabinets
- Wall cabinets
- Tall cabinets, pantries and appliance openings
- What Mexican shops typically build
- From cabinet size to cut list
- How depth choices change sheet yield
- Ergonomics: when to break the standard
- Quick checklist before you lock dimensions
- From dimensions to a cut list without retyping
US kitchen cabinets are about as standardized as anything in woodworking: walk into any big-box store and the base cabinets are 34½ inches tall and 24 inches deep, every time. Mexico is different. There’s no official Mexican standard for kitchen cabinet dimensions; shops follow local habit, appliance specs and, quite often, the US numbers. This guide lays out the US standards, the dimensions Mexican shops typically build to, and what both mean for your cut list and your sheet count. Treat every number here as a common starting point, not a rule.
The key dimensions at a glance
The section below shows the four dimensions people ask about most: counter height, base cabinet depth, the gap between countertop and wall cabinets, and wall cabinet height and depth.
| Dimension | US (catalog standard) | Mexico (typical) |
|---|---|---|
| Finished counter height | 36 in (914 mm) | ≈ 90 cm (35½ in) |
| Base cabinet height | 34½ in (876 mm) incl. toe kick | 72–76 cm box + 10–12 cm toe kick |
| Toe kick (height × depth) | ≈ 4 in × 3 in | 10–12 cm × 5–7 cm |
| Base cabinet depth | 24 in (610 mm) | 55–58 cm box |
| Countertop depth | 25–25½ in | 60–62 cm |
| Wall cabinet depth | 12 in (305 mm) | 30–35 cm |
| Wall cabinet height | 30, 36, 42 in | 60, 70, 90 cm |
| Counter to wall cabinet | 18 in (457 mm) | 50–60 cm |
| Widths | 9–48 in in 3 in steps | 30, 40, 45, 50, 60, 80, 90 cm |
| Tall / pantry | 84, 90, 96 in × 24 in | 200–220 cm × base depth |
Base cabinets
Height: how you get to 36 inches
A US base cabinet is 34½ in tall with the toe kick included, and a standard 1½ in countertop brings it to 36 in. In a frameless (European-style) shop that builds boxes on a separate toe kick base, the stack usually looks like this:
36 in = 4½ in + 30 in + 1½ in
(in metric: 114 + 762 + 38 = 914 mm)
If the client picks a thinner top, such as ¾ in quartz on a substrate or a 1¼ in slab, adjust the box or the toe kick so the finished height still lands where you agreed. Ask the countertop fabricator for the real thickness before you cut, not after.
Depth
Base cabinets are 24 in deep to the face of the door in most catalogs. In a frameless build that’s roughly a 23¼ in box plus a ¾ in door. The countertop runs 25 to 25½ in so it overhangs the doors by about an inch and sheds water away from the cabinet faces. Sink bases, cooktops with drawers below and dishwashers all eat into that depth, so check the clear interior depth before you commit.
Widths
Stock base cabinets come from 9 to 48 in in 3 in increments. The workhorses are 12, 15, 18, 24, 30 and 36 in. Sink bases are most often 36 in (30 and 33 in are common too), and drawer bases usually run 12 to 24 in. Anything wider than about 24 in gets two doors. Filler strips of 1 to 3 in close the run against walls and keep doors and handles from hitting adjacent surfaces.
Wall cabinets
Standard wall cabinets are 12 in deep and 30, 36 or 42 in tall. With an 18 in backsplash gap over a 36 in counter, a 30 in wall cabinet tops out at 84 in, the classic line for an 8 ft ceiling with a soffit or crown above; 42 in cabinets run nearly to the ceiling. Above the refrigerator you’ll find short wall cabinets, often 12 to 18 in tall and sometimes 24 in deep to match the fridge. Over the range, the hood manufacturer’s installation sheet sets the minimum clearance above the cooking surface, and it’s usually more than 18 in, so plan that cabinet separately.
Tall cabinets, pantries and appliance openings
Tall units such as pantries, oven towers and broom closets are made 84, 90 or 96 in tall to line up with the tops of the wall cabinets, and 24 in deep to line up with the base fronts (12 in deep pantries exist too). If a tall unit runs to the ceiling, leave room to tilt it into place: a 96 in cabinet won’t stand up under a 96 in ceiling.
Appliance openings are where “standard” stops being safe. A 30 in range, a 24 in dishwasher and a 36 in refrigerator opening are common, but built-in ovens, column refrigerators and panel-ready dishwashers each have exact cutout dimensions, ventilation gaps and door-swing requirements in their install guides. A refrigerator jammed against a tall cabinet that can’t open past 90° won’t let the crisper drawers out.
What Mexican shops typically build
If you work with clients or partners in Mexico, or you’re reading plans that came from there, expect metric round numbers. Finished counter height usually lands around 90 cm (just under 35½ in), built from a 72–76 cm box, a 10–12 cm toe kick (zoclo) and the countertop. Base boxes run 55–58 cm deep, countertops 60–62 cm, and wall cabinets (alacenas) 30–35 cm deep and 60, 70 or 90 cm tall, with a 50–60 cm gap above the counter. Widths come in round centimeters: 30, 40, 45, 50, 60, 80 and 90 cm. The inch to millimeter converter handles fractional inches both ways.
From cabinet size to cut list
Catalog dimensions are outside dimensions. To cut, you need parts, and that’s where material thickness comes in. Take a 24 in frameless base cabinet with a 30 in box on a toe kick base, ¾ in sides running full height and the bottom captured between the sides. In metric the logic is identical: a 600 mm cabinet with 18 mm sides has a bottom of 600 − 2 × 18 = 564 mm.
Bottom (1) = (width − 2 × side thickness) × depth
= (24 − 2 × ¾) × 23¼ = 22½ in × 23¼ in
Top stretchers (2) = 22½ in × 4 in
Doors (2), 1⁄16 in reveal at each side and ⅛ in at center:
width = (24 − 2 × 1⁄16 − ⅛) ÷ 2 = 11⅞ in
Reveals depend on your hinges and your shop’s habits; the door size calculator does the arithmetic for one or two doors. If you band the parts, remember the banding thickness also comes off the cut size.
How depth choices change sheet yield
Cabinet sides, shelves and wall cabinet parts come out of the sheet as rips, so their depth decides how many fit across the panel. On a 48 in wide sheet with a ⅛ in kerf:
Base sides at 24 in: 2 × 24 + ⅛ = 48⅛ in → doesn’t fit
Wall sides at 11¾ in: 4 × 11¾ + 3 × ⅛ = 47⅜ in → fits
Wall sides at 12 in: 4 × 12 + 3 × ⅛ = 48⅜ in → only 3 fit
That’s one reason a “12 inch” wall cabinet box is often built a bit shallower, with the door bringing the front to about 12 in. If you trim factory edges, you lose even more width; some suppliers sell oversized panels to leave room for that, so check what yours carries. The same logic applies to metric sheets: on a 1830 mm panel with a 10 mm trim per edge and a 4 mm kerf, six 300 mm wall sides need 1820 mm and won’t fit in the 1810 mm usable width, while six at 295 mm will. Grain-matched melamine adds another constraint because sides must keep the grain vertical. The guide on how many sheets a kitchen needs walks through a full example.
Ergonomics: when to break the standard
- Counter height: a common rule of thumb puts the work surface 4 to 6 in below the elbow of whoever cooks most. Tall households often prefer 37–38 in; shorter cooks, 34–35 in.
- Reach: everyday items belong between hip and shoulder height. Drawer bases and the lower shelves of wall cabinets get far more use than the top shelf.
- Aisles: leave room to open a door or drawer and walk past at the same time; about 42 in is a common minimum for a one-cook kitchen.
- Over the sink: for tall clients, raise the wall cabinet or drop to a shallower box so they don’t hit their head while washing.
Quick checklist before you lock dimensions
- Actual countertop thickness and who installs it.
- Install sheets for range, hood, oven, refrigerator and dishwasher.
- Plumbing, outlets and gas lines marked on the wall.
- Floor out of level and walls out of square (plan fillers and scribe).
- Sheet thickness and edge banding thickness you’ll actually use.
From dimensions to a cut list without retyping
In the Zeder Studio Design module you lay out the kitchen with your shop’s dimensions, then send it to Cut to optimize the sheets or to Quote to price it. If a cabinet has no recipe in your catalog, generic formulas are used and the app warns you to review the parts. See how that looks for kitchen cabinet shops, or continue with how to quote a kitchen.
Save this, optimize the cut list and quote it in Zeder Studio.
Frequently asked questions
What is the standard kitchen counter height in the US?
36 inches finished: a 34½ in base cabinet (toe kick included) plus a 1½ in countertop. Adjust the box or toe kick if the countertop is thinner or thicker.
How deep are standard base and wall cabinets?
Base cabinets are 24 in deep with a 25 to 25½ in countertop, and wall cabinets are 12 in deep. Mexican shops typically build 55–58 cm base boxes and 30–35 cm wall cabinets.
How much space goes between the countertop and wall cabinets?
The US standard is 18 in. Over a range, the hood manufacturer’s installation sheet sets the minimum clearance, which is usually more.
How do I get the bottom panel size from the cabinet width?
If the bottom sits between the sides, subtract two side thicknesses from the outside width: a 24 in cabinet with ¾ in sides gets a 22½ in bottom (600 − 2 × 18 = 564 mm in metric).
Is there an official cabinet dimension standard in Mexico?
No. Mexican shops follow common practice, appliance specs and often the US catalog sizes, so always confirm dimensions with the client and the appliance install sheets.
Keep reading
How many sheets a kitchen needs
How to work out melamine and back panel sheets for a kitchen: parts per cabinet, a 3-meter worked example, realistic waste and common mistakes.
How to quote kitchen cabinets
How to price a kitchen cabinet job: measure, build the cut list, cost sheets, edge banding, hardware and labor, then set your price. With a worked example.
Cabinet door size
Work out overlay or inset door sizes, single or pairs, from the opening, overlay and gaps.
mm to inches
Convert millimeters to fractional inches (1/16, 1/32, 1/64) and inches like 23 7/8 back to millimeters. Built for the shop.
Cabinet design
Design kitchens, closets and vanities cabinet by cabinet, review them in 3D and send the cut list straight to the optimizer. Nothing to install.
Kitchen cabinet makers
Design the kitchen, get the cut list, optimize the sheets and quote with real costs. One workflow for kitchen cabinet shops.
Cut better starting with your next job
Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.