How to quote kitchen cabinets step by step
- Type
- Guide
- Updated
- Reading time
- 7 min
- Sections
- 14
On this page (14)
- 1. Measure the site
- 2. Settle the layout and the cabinet list
- 3. Build the cut list
- 4. Count sheets per material
- 5. Edge banding
- 6. Hardware
- 7. Countertop: its own line, or excluded
- 8. Labor, in hours
- 9. Delivery, overhead and waste
- 10. Setting the price: markup vs. margin
- 11. Tax, payment schedule, validity and terms
- Worked example: a 3-meter straight kitchen
- Common mistakes
- How it works in Zeder Studio
Pricing a kitchen by gut feel works right up until a job loses money: the wall-cabinet hangers never made the list, the customer assumed the countertop was included, or the delivery across town turned into two truck trips. This guide is the method we use in a melamine cabinet shop so every quote comes out of the same process, with numbers you can stand behind when the customer pushes back.
At the end there’s a full worked example: a 3-meter (about 10-foot) straight kitchen, line by line, from direct cost to the total with tax.
1. Measure the site
Every mistake you make on site gets paid for in the shop. Bring a tape, a level and a square, use a measuring sheet, and record:
- Walls: length of each wall at three heights (bottom, middle, top) and floor-to-ceiling height at several points. Walls are rarely plumb and corners are rarely square.
- Utilities: water supply, drain, gas valve, outlets, switches and the panel, with distance from the corner and height off the floor.
- Openings: windows (sill height), doors, columns and soffits.
- Appliances: range or cooktop, wall oven, hood, refrigerator, sink and dishwasher. Ask for model numbers or spec sheets; cutout dimensions aren’t the same as appliance dimensions.
2. Settle the layout and the cabinet list
With measurements in hand, decide the shape: straight, L-shaped, U-shaped, with an island or galley. Every corner adds a blind or corner cabinet, and those usually cost more than a straight cabinet of the same width.
Then split each run into cabinets: bases, wall cabinets, tall units, drawer bases. Write down width, height, depth and type (doors, drawers, sink, cooktop). For reference sizes, see standard kitchen cabinet dimensions. Whatever doesn’t close with standard widths becomes a filler, and fillers get priced too.
3. Build the cut list
The cut list is every part of every cabinet: sides, bottoms, stretchers, shelves, tops, backs, doors, drawer fronts and toe kick, each with size, material and edge banding. Everything else is built on it. Without a cut list you don’t know how many sheets to buy or how many feet of banding to run.
4. Count sheets per material
Split the cut list by material (boxes, doors, backs) and work out sheets for each. The area method and its traps are covered in how many sheets a kitchen needs, and the sheet calculator runs the numbers. For a quote, an area estimate with your usual waste is enough; for the order, confirm with the optimizer.
5. Edge banding
Add up banding by color and thickness: usually all four edges of doors and drawer fronts, plus the front edge of box sides, bottoms, shelves and tops. Add an allowance per edge (the overhang you trim off) and a waste percentage. The edge banding calculator does it and tells you how many rolls you need.
6. Hardware
Count it piece by piece, never as “hardware, allow”:
- Cup (35 mm) hinges: two per door up to a certain height, three or more on tall or heavy doors. Decide on soft-close up front.
- Drawer slides: one pair per drawer, sized to the box depth (side-mount, undermount, soft-close).
- Pulls or knobs: one per door and drawer, or feet of profile for handleless designs.
- Leveling legs and toe-kick clips: usually four legs per base, more on wide bases.
- Wall-cabinet hangers or rail, shelf pins, screws, glue, screw caps and caulk.
7. Countertop: its own line, or excluded
Countertops (granite, quartz, laminate) are usually priced separately because another fabricator templates and installs them. What matters is that it’s in writing: “countertop not included”, or a line with its own size and price. It’s the number-one source of misunderstandings with customers.
8. Labor, in hours
Price labor in hours, not as a percentage of material. Break it into stages because each moves at its own pace: cutting, edge banding, assembly and installation. Use real times from recent jobs and multiply by your loaded shop rate (wages, benefits and payroll taxes divided by productive hours, not paid hours).
9. Delivery, overhead and waste
- Delivery: per trip, keeping in mind a kitchen may take more than one, and stairs slow things down.
- Overhead: rent, power, blades, maintenance, office time. Add it as a percentage of direct cost or of labor, or as a fixed amount per job.
- Waste: if you’re already pricing whole sheets (rounded up), waste is built in. Don’t stack another percentage on top.
10. Setting the price: markup vs. margin
More money gets lost to this mix-up than to anything else. “I make 35% on it” can mean two very different things:
Gross margin: price = cost ÷ (1 − %)
Cost $2,648.22 at 35% markup → $3,575.10 (actual margin 25.9%)
Cost $2,648.22 at 35% margin → $4,074.18 (equivalent markup 53.8%)
If your goal is to keep 35 cents of every dollar you bill, you need margin, not markup. Try your own numbers in the markup and margin calculator.
11. Tax, payment schedule, validity and terms
In the US, sales tax on cabinet work depends on your state and on how the job is structured. In many states installed cabinetry is treated as a construction contract where you pay tax on materials rather than charging it on the total. Check with your accountant. In Mexico, IVA is generally 16%, applied last on the subtotal after discounts.
A common practice is a 50% or 60% deposit to buy material and the balance at installation (50/50 or 60/40). It isn’t a rule, it’s an agreement, and it belongs in writing along with how long the quote is valid (sheet prices move) and what’s included and excluded.
| Spell out as included | Spell out as excluded (if so) |
|---|---|
| Box and door materials, with colors | Countertop and sink |
| Hardware (hinge and slide type or brand) | Appliances and hookups |
| Fabrication and installation | Plumbing, gas and electrical |
| Local delivery | Tear-out, drywall patching and paint |
Worked example: a 3-meter straight kitchen
Five bases (600, 600, 800, 500 and 500 mm, roughly 24", 24", 31", 20" and 20") and four 600 mm wall cabinets; 5/8" white melamine boxes, 16 wood-grain melamine doors, 1/8" backs, no drawers. Sheet counts come from the example in the sheets guide; banding footage includes a 30 mm (1 3/16") allowance per edge and 10% waste.
| Line | Qty | Unit cost | Amount |
|---|---|---|---|
| White melamine 5/8", 2440 × 1830 mm | 4 sheets | $60 | $240.00 |
| Wood-grain melamine 5/8", 2440 × 1830 mm | 2 sheets | $90 | $180.00 |
| Hardboard 1/8", 4 × 8 | 2 sheets | $20 | $40.00 |
| Wood-grain edge banding 3/4" | 128 ft | $0.35 | $44.80 |
| White edge banding 3/4" | 115 ft | $0.20 | $23.00 |
| Soft-close cup hinge | 32 | $4 | $128.00 |
| Pull | 16 | $5 | $80.00 |
| Leveling leg with toe-kick clip | 20 | $2 | $40.00 |
| Wall-cabinet hanger | 8 | $4 | $32.00 |
| Screws, shelf pins, glue | 1 lot | $45 | $45.00 |
| Materials | $852.80 | ||
| Shop labor: cutting 4 h, banding 4 h, assembly 10 h | 18 h | $45 | $810.00 |
| Installation (2 people × 6 h) | 12 h | $45 | $540.00 |
| Local delivery | 1 trip | $100 | $100.00 |
| Countertop | Not included (quoted separately) | ||
Overhead 15% = 2,302.80 × 0.15 = $345.42
Total cost = $2,648.22
Price at 35% margin = 2,648.22 ÷ 0.65 = $4,074.18
Gross profit = $1,425.96
Sales tax, if it applies (example 7%) = $285.19
Total = $4,359.37
50/50 schedule = $2,179.69 on signing + $2,179.69 at install
Price it at a 35% markup instead and the subtotal is $3,575.10: $499.08 less on a single job, with nothing different in the shop.
Common mistakes
- Mixing up markup and margin (see above).
- Pricing labor as a percentage of material: pricier melamine doesn’t take longer to assemble.
- Forgetting the small hardware: hangers, legs, clips, shelf pins, caps.
- Not stating in writing whether countertop, sink or appliance install are included.
- Adding waste twice: once by rounding sheets up and again as a percentage.
- Calculating tax before the discount, or not saying whether the price is “plus tax”.
- No expiration date, then honoring a three-month-old price after sheet goods went up.
How it works in Zeder Studio
Draw the kitchen in the Design module. Each cabinet generates its parts, banding and hardware.
Under Entregables → Enviar a Cotización (Deliverables → Send to Quote), a numbered design revision is created and a new quote opens with lines already filled from that cut list. If you’ve already optimized, you can also start the quote from the cut plan, with the sheets it actually uses.
Adjust the lines: labor hours, installation, delivery, waste, discounts. Choose Markup or Gross margin; the summary shows the equivalent, the profit, and warns you with “Low margin” or “You lose money at this price”.
Add overhead, tax (pulled from your settings), the payment schedule (must add up to 100%), validity and terms.
Send and freeze locks that version so amounts no longer recalculate. Share it with the Customer link: your customer opens it without an account and accepts or declines online.
Details are in the help articles for Quotes and sending and freezing a quote. The Quote module is part of the free trial.
Save this, optimize the cut list and quote it in Zeder Studio.
Frequently asked questions
How much does a melamine kitchen cost?
It depends on run length, materials, hardware and your shop rate. The method in this guide gets you your real cost and a price at the margin you need, instead of a blind per-foot number.
Should I price kitchens per linear foot?
It works as a quick ballpark, but it hides big differences between a kitchen full of drawers, tall units and corners and one with plain door bases. For the formal quote, cost it line by line.
What’s the difference between markup and margin?
Markup is a percentage of cost; margin is a percentage of the selling price. A 35% margin equals roughly a 54% markup.
How big a deposit should I ask for on a kitchen?
Many shops ask for 50% or 60% up front and the balance at installation, but it isn’t a rule. Whatever you agree on, put it in the quote.
Does sales tax go on the whole kitchen?
It depends on your state and how the job is contracted; in many states installed cabinets are taxed on materials rather than on the total price. Confirm with your accountant.
Keep reading
Quoting
Quote from real sheet, edge band, hardware and labor costs. Markup or margin, taxes, deposits, a branded PDF and online acceptance.
Markup vs. margin
Price a job from its cost with markup or margin and see both side by side. Stop underpricing your quotes.
How many sheets a kitchen needs
How to work out melamine and back panel sheets for a kitchen: parts per cabinet, a 3-meter worked example, realistic waste and common mistakes.
Edge banding calculator
Calculate how many meters of edge banding you need per part and edge, with trim allowance and waste, and how many rolls to buy.
Lines, pricing and taxes
Build a quote with lines and sections, choose markup or margin, add waste, overhead, discounts, taxes and payment milestones.
Send a quote and get it accepted
Send and freeze a version, share the PDF or the online link so the customer can accept, create new versions and release it to production.
Cut better starting with your next job
Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.