Skip to content

How many sheets of melamine does a kitchen need?

How to work out melamine and back panel sheets for a kitchen: parts per cabinet, a 3-meter worked example, realistic waste and common mistakes.
Type
Guide
Updated
Reading time
7 min
Sections
9
On this page (9)

“How many sheets do I need for this kitchen?” There is no fixed answer, and anyone who gives you one without seeing the cut list is guessing. A 10-foot kitchen can take four sheets or seven depending on the number of boxes, their depth, whether the doors are a different material and how well each sheet gets used. What you can have is a method that gives you the number for your kitchen in about ten minutes, and a way to confirm it before you order material.

Below we build the cut list for a 3-meter (about 10-foot) straight kitchen, estimate sheets by area, look at where that estimate breaks down and show how an optimizer gets you the exact count. The example is metric, the way we build in Mexico, with inch equivalents. A US kitchen with 3/4" boxes and 24" deep bases works exactly the same way.

Why there’s no “one kitchen = X sheets” rule

Rules of thumb are fine for a ballpark on the phone. They are not fine for a material order, because too much changes from job to job:

  • Number and width of boxes. Ten 12" cabinets need far more sides than five 24" cabinets covering the same wall.
  • Box depth. A 22" side and a 23 5/8" side look almost the same, but they change how many strips you get out of a sheet (see how to reduce sheet waste).
  • Different materials. Boxes are usually white or gray melamine; doors are a solid color or a wood-grain. Each material is its own calculation. You don’t add them together.
  • Drawers, tall units and extra shelves. A three-drawer base has many more parts than a door base of the same width.
  • Grain. Wood-grain doors can’t be rotated, which raises waste.

The parts in each cabinet

You need a cut list before you can count sheets. In frameless melamine construction, where every cabinet is its own box, a typical breakdown looks like this:

Base cabinet

  • 2 sides (box height × depth).
  • 1 bottom (cabinet width minus two side thicknesses × depth).
  • 2 stretchers across the top, front and back, about 4" (100 mm) wide. Some shops use a full top instead.
  • 1 adjustable shelf, slightly narrower and shallower than the bottom. Sink bases usually skip it.
  • 1 back in 1/8" or 1/4" (3 or 6 mm) hardboard or MDF, counted separately.

Wall cabinet

  • 2 sides, a top, a bottom and one or two shelves.
  • 1 thin back. If you hang wall cabinets on a rail or hangers, check whether your system needs a thicker back or a hanging strip.

Doors and toe kick

Doors and drawer fronts are almost always a different material. The toe kick may match the boxes, match the doors or be aluminum or PVC. Decide that before counting sheets, since it changes which pile each part lands in. If you need the box sizes first, start with standard kitchen cabinet dimensions.

Worked example: a 3-meter straight kitchen

Picture a typical apartment kitchen: 5 base cabinets and 4 wall cabinets. Boxes in 16 mm (5/8") white melamine, doors in 16 mm wood-grain melamine, 3 mm (1/8") backs. Bases are 720 mm tall × 560 mm deep (about 28 3/8" × 22", for a 600 mm countertop) on legs with a 100 mm (4") toe kick. Wall cabinets are 700 × 330 mm (27 9/16" × 13"), with an open space for the range hood.

W1 · 600W2 · 600W3 · 600W4 · 600hoodB1 · 600B2 · 600B3 · 800B4 · 500B5 · 500toe kick3000 mm
Elevation of the example kitchen: bases of 600, 600 (cooktop), 800 (sink), 500 and 500 mm; four 600 mm wall cabinets and the hood opening.

Box parts (16 mm white melamine)

PartQtySize (mm)Area (m²)
Base side10720 × 5604.03
Base bottom5(width − 32) × 5601.59
Base stretcher (front and back)10(width − 32) × 1000.57
Base shelf (not in sink base)4(width − 34) × 4800.99
Wall side8700 × 3301.85
Wall top and bottom8568 × 3301.50
Wall shelf4566 × 3000.68
Toe kick (two pieces)21500 × 1000.30
Total, boxes5111.51

“Width − 32” is the cabinet width minus two 16 mm sides. With bases of 600, 600, 800, 500 and 500 mm, the bottoms add up to 2,840 mm of length. Note the toe kick: 3 m won’t come out of a 2440 mm (8 ft) sheet, so it goes in two pieces. Plan the seam behind a leg or at a corner. (11.51 m² is about 124 sq ft.)

Doors (16 mm wood-grain melamine)

Full-overlay doors with a 3 mm gap: the 600 mm bases get two 297 × 715 doors each, the 800 mm sink base two 397 × 715, the 500 mm bases one 497 × 715 each, and each wall cabinet two 297 × 697. That is 16 doors and 3.78 m² (about 41 sq ft).

Backs (3 mm hardboard / thin MDF)

Five base backs 720 mm tall (widths adding up to 3,000 mm) and four wall backs at 600 × 700: 3.84 m².

The area method, step by step

This is what the sheet calculator does: add up part area, add a waste percentage and divide by the sheet’s usable area, which is the sheet minus the edge trim on each side.

Sheets = ⌈ part area × (1 + waste) ÷ usable area ⌉
Usable area (2440 × 1830, 10 mm trim) = 2420 × 1810 = 4.38 m²

Boxes, 10%: 11.51 × 1.10 = 12.66 m² ÷ 4.38 = 2.89 → 3 sheets
Boxes, 15%: 11.51 × 1.15 = 13.23 m² ÷ 4.38 = 3.02 → 4 sheets
Doors, 20% (grain): 3.78 × 1.20 = 4.54 m² ÷ 4.38 = 1.04 → 2 sheets
Backs, 10%: 3.84 × 1.10 = 4.22 m² ÷ 2.90 = 1.46 → 2 sheets (2440 × 1220 or 4 × 8)

Always round up; you can’t buy 2.89 sheets. And look at the boxes: moving from 10% to 15% waste flips the answer from 3 sheets to 4. That waste figure isn’t a constant. It depends on part shapes, grain and how you cut. So the area method is a good number for a quote, not the final number for an order.

Sheet sizes and usable area

SheetWhere it’s commonFull areaUsable (10 mm trim)
4 × 8 ft (48" × 96", 1219 × 2438 mm)United States32 sq ft (2.97 m²)2.90 m²
2440 × 1220 mmMDF, hardboard, plywood in Mexico2.98 m²2.90 m²
2440 × 1830 mm (≈ 8 × 6 ft)Melamine in Mexico4.47 m²4.38 m²

Check the actual size with your supplier. Not every brand runs the same sizes, and a “4 × 8” is not exactly 1220 × 2440 mm. More in standard sheet sizes.

Where the area method goes wrong

Area math assumes parts pour into the sheet like water. On a panel saw they don’t:

  • Long or wide parts. A 720 × 560 side leaves strips that don’t always get used. When parts are large compared to the sheet, area underestimates.
  • Grain. Doors locked lengthwise leave the layout fewer options.
  • Sizes that “almost” fit. Two 600 mm parts won’t come out of a 1220 mm sheet width once you trim the edges and cut with a 4 mm blade.

It can also go the other way. In our example, area at 20% says 2 sheets of door material. Lay the 16 doors out by hand on one 2440 × 1830 sheet, grain running lengthwise, and they fit in three rows (715 + 715 + 697 mm) with a strip of almost 290 mm (11") to spare. A good layout needs one sheet. Area math would have had you buy an extra one.

Getting the exact count: the optimizer

The number to order from comes from laying real parts on real sheets, with your blade kerf, your trim and the grain of each material. That’s what the free cut optimizer does: enter the cut list, pick the sheet, and it returns the sheet count, the yield and a cutting diagram for each sheet.

For the example, run boxes, doors and backs as three lists, or one list with the right material on each part. In Zeder Studio’s Cut module you can also save the job, use offcuts from earlier jobs and, if you drew the kitchen in Design, send the cut list straight over instead of typing it.

Common mistakes when counting sheets

  • Lumping materials together. 11.5 m² of white and 3.8 m² of wood-grain is not “15.3 m² of melamine”. They are two separate orders.
  • Forgetting parts. The usual suspects: backs, toe kick, shelves, stretchers, fillers and finished end panels.
  • Ignoring grain on wood-grain melamine. If the layout rotates a door, the pattern runs sideways and the part gets recut.
  • Treating 4 × 8 and 2440 × 1220 as the same. A few millimeters decide whether two parts fit side by side.
  • Not rounding up, or adding waste twice (once on the parts, again on the sheets).
  • Dividing by the full sheet area instead of the usable area after trim.

Summary

Break each cabinet into parts, split by material, add up area, apply your real waste, divide by usable area and round up. Use that number to quote, then confirm it with the optimizer before you order. For the example kitchen that’s 3–4 sheets for boxes, 1–2 for doors and 2 for backs: a sensible range the optimizer narrows to one number.

Save this, optimize the cut list and quote it in Zeder Studio.

Frequently asked questions

How many sheets of melamine does a 10-foot kitchen need?

It depends on cabinet count, depth and materials. A 3 m straight kitchen with 5 bases and 4 wall cabinets typically lands at 3–4 sheets of 2440 × 1830 mm for boxes, 1–2 for doors and 2 sheets of backer; confirm with the optimizer.

What waste percentage should I use?

Many shops use 10–20%, higher for wood-grain melamine. The best number is your own: compare sheets bought against part area on past jobs.

Do cabinet backs count as melamine?

No. Backs are usually 1/8" or 1/4" hardboard or MDF and are calculated separately, typically on 4 × 8 sheets.

Why does the optimizer give a different number than the area method?

It places the real parts with kerf, trim and grain. Area is an average; the optimizer tells you how many sheets the layout actually uses.

Can I calculate sheets for free?

Yes. The sheet calculator and the cut optimizer are free with no sign-up; the optimizer takes up to 50 parts.

Cut better starting with your next job

Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.