Skip to content

Edge banding calculator: meters and rolls to buy

Pick which edges of each part get banding and get the total meters with trim allowance and waste.
Banded parts (mm)
mm

Trimmed off at the ends

%
m

Result

Edges to band
28
Net meters
16.03 m
Meters to buy
18.6 m
Rolls
1

Save this, optimize the cut list and quote it in Zeder Studio.

On this page (5)

Edge banding is bought by the foot or by the roll, and it’s usually eyeballed. This calculator does it part by part, edge by edge, and adds what gets lost at the ends and in the edgebander.

How the calculation works

Net meters = Σ qty × (long edges × length + short edges × width) ÷ 1000
Edges = Σ qty × (long edges + short edges)
Meters to buy = (net + edges × allowance ÷ 1000) × (1 + waste % ÷ 100)
Rolls = round up (meters to buy ÷ roll length)

Long edges use the part’s Length and short edges its Width, 0 to 2 of each. The allowance is the overhang trimmed off at each end, added once per banded edge. Waste covers bander start-up, damaged runs and roll ends. Inputs are in millimeters and meters (1 m ≈ 3.28 ft).

Worked example

With the calculator’s defaults: 30 mm (about 1 3/16") allowance, 10% waste and a 50 m (164 ft) roll.

PartSize (mm)QtyBanded edgesNet (mm)Edges
Side720 × 56041 long4 × 720 = 2,8804
Shelf700 × 39662 long + 2 short6 × 2,192 = 13,15224
Total16,03228
Allowance: 28 × 30 = 840 mm
(16,032 + 840) × 1.10 = 18,559 mm
Meters to buy: 18.6 m (about 61 ft) → 1 roll of 50 m

16.03 net meters (52.6 ft) become 18.6 real meters: almost 16% more. That’s the cushion most bids forget.

Which edges get banding on a typical box

Every shop has its own rules, but on frameless melamine cabinets it usually looks like this:

  • Sides: the front edge; the back edge only if it shows.
  • Top and bottom: the front edge.
  • Shelves: the front, or all four edges on open shelving that shows from every side.
  • Doors and drawer fronts: all four edges, usually with thicker banding.
  • Backs and hidden parts: none.

Common mistakes

  • Banding everything. Edges against a wall or hidden inside another cabinet usually don’t need it. Band only what shows.
  • Mixing band types. Thin interior banding and thick banding for doors and fronts are separate purchases: calculate each one separately.
  • Ignoring allowance on small parts. On a 4" part, 1 3/16" of overhang is almost a third more.
  • Guessing roll length. It depends on the supplier, the width and the thickness; check with yours.
  • Not deducting banding from the cut size. With thick banding the part grows. The app has Deduct edge band from cut size (see optimization settings).

Tips

  • Set the allowance to your method: an automatic edgebander usually needs less than hand-applied, iron-on banding.
  • Record the result per job and compare it with what you actually used; after three or four jobs you’ll know your real waste.
  • To choose type and thickness (PVC, ABS, melamine, wood veneer), read edge banding types and how to calculate it.
  • Carry the meters into your bid as an edge banding line with its waste in the Quote module, and set your price with the margin calculator.

Need the sheets too? Use the sheet calculator with the same cut list, so the banding and the sheet goods on your bid come from the same parts and quantities.

Frequently asked questions

How do I calculate edge banding for a cabinet?

For each part, add up the banded edges, multiply by the quantity, then add an allowance per edge and a waste percentage. The calculator does it for you.

How much allowance should I leave per edge?

It depends on how you band. The calculator starts at 30 mm (about 1 3/16 in) per edge; adjust it to what you actually trim off.

How long is a roll of edge banding?

It varies by supplier, width and thickness. Check the length with your distributor and enter it as the roll length.

Cut better starting with your next job

Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.