Edge banding types and how to calculate it
- Type
- Guide
- Updated
- Reading time
- 6 min
- Sections
- 7
On this page (7)
Edge banding is the strip that covers the raw, cut edge of a panel. On melamine it isn’t just cosmetic: it’s what keeps moisture and dings out of the particleboard or MDF core. Pick the wrong band or miscount it and you pay twice, once when edges start peeling a few months in and again when you’re short thirty feet halfway through a job. Here are the types, the common sizes and the math so you order the right amount.
Types of edge banding
PVC
The workhorse for melamine. It’s flexible, impact- and moisture-resistant, and suppliers match it to their melamine colors and wood-grain patterns. Thin versions go on box edges; thick ones on doors and drawer fronts.
ABS
Looks and machines almost exactly like PVC but is chlorine-free, which some manufacturers and clients prefer. It usually costs a bit more and runs through an edgebander much the same way.
Melamine (paper) banding
A thin, stiff strip of resin-saturated paper, often pre-glued so you can apply it with a household iron. It’s inexpensive and handy for hidden or low-wear edges, but it chips when bumped, so keep it off doors and work surfaces.
Wood veneer
A thin slice of real wood, plain or pre-glued (the familiar iron-on veneer tape). It’s the match for veneered panels and plywood that will be stained or clear-coated: you sand and finish it along with the face.
Acrylic and 3D banding
Clear acrylic printed on the back, which gives a glass-like depth effect. It’s used on high-gloss fronts and modern designs and needs more care when trimming and buffing.
Common thicknesses and widths
The usual thicknesses are 0.45 mm (often sold as 0.018 in), 1 mm and 2 mm (about 0.04 and 0.08 in), with 3 mm for heavy-duty edges. Common widths run 19, 22, 28 or 29, 35 and 45 mm (roughly ¾, ⅞, 1⅛, 1⅜ and 1¾ in), but every supplier has its own list, so check before you design. The band should be a little wider than the panel is thick so there’s something to trim flush:
| Panel | Typical band width | Where each thickness goes |
|---|---|---|
| ⅝ in (15–16 mm) | ¾ in (19 mm) | 0.45 mm on hidden edges, 1 mm on box fronts |
| ¾ in (18–19 mm) | ⅞ in (22 mm) | 2 mm on doors, drawer fronts and high-traffic edges |
| 1 in or doubled panels | 1⅛–1⅜ in (28–35 mm) | Depends on use: thick shelves, worktops |
| Built-up tops | 1⅜–1¾ in (35–45 mm) | Heavy band to take daily wear |
The rule of thumb: 2 mm on anything people see and touch (doors, drawer fronts, the front edge of an exposed shelf) and 0.45 mm on edges that stay hidden or protected (back edges, edges inside the box). One-millimeter banding is a sensible middle ground for the front edges of box sides and bottoms.
How it’s applied
By hand
Pre-glued banding goes on with an iron, then gets pressed down with a block or J-roller while the glue sets. Unglued PVC can be applied with contact cement on both surfaces. Then you trim the overhang with a hand edge trimmer or a utility knife and ease the arris with a sanding block. It’s fine for repairs, one-off parts and shops that don’t have a machine yet, but slow for a full kitchen.
With an edgebander
An edgebander applies hot-melt glue, presses the band on and, depending on the model, end-trims, flush-trims top and bottom, rounds corners, scrapes and buffs. The two common adhesives are:
- EVA: the everyday choice; easy to reheat and forgiving. Less resistant to heat and moisture.
- PUR: thinner glue line and better moisture and heat resistance, worth it in kitchens and baths. The machine needs more careful cleaning.
Trimming and edge radius
Flush-trimming removes the overhang at the top, bottom and ends. On 2 mm banding, the trimmer and scraper usually leave a small radius on the edge, which feels better and stands up to knocks far better than a sharp corner.
Deducting banding from the cut size
A 2 mm band adds 2 mm to every banded side. If the size on the drawing is the finished size, you have to cut the part smaller so it lands exactly once the band is on:
700 × 400 mm part, 2 mm on both long edges → width = 400 − 2 × 2 = 396 mm · length = 700
Door 30 × 14⅞ in, 2 mm on all four edges → 4 mm (about 5⁄32 in) smaller each way
With 0.45 mm banding many shops don’t bother deducting, since it falls inside the cut tolerance; with 1 and 2 mm banding, you should. The Cut module in Zeder Studio has a setting that deducts banding thickness from the cut size, and every part carries its banding per side (top, bottom, left and right) using the band thickness set on the material. Details in cut settings.
How to calculate how much banding to buy
Work it out per part and per edge, then add two things: an allowance per edge, because the band has to overhang at both ends for the end trim (about 1 in, or 2–3 cm, is typical), and a waste percentage for start-ups, test pieces, mistakes and the tail end of the roll.
total = (net length + number of edges × allowance) × (1 + waste %)
rolls = total ÷ roll length, rounded up
That’s exactly what the free edge banding calculator does. It takes millimeters, so multiply inches by 25.4 or use the result below as a sanity check.
Worked example: a simple frameless kitchen
Four 30 in base cabinets and three 30 in wall cabinets, each with two doors. Doors get 2 mm PVC on all four edges; box parts get thin banding on the front edge only. A 1 in allowance per edge and 10% waste:
| Part | Size (in) | Qty | Banded edges | Band | Net in | Edges |
|---|---|---|---|---|---|---|
| Doors (base and wall) | 30 × 14⅞ | 14 | 2 long + 2 short | 2 mm | 1,256.5 | 56 |
| Base sides | 30 × 23¼ | 8 | 1 long | Thin | 240 | 8 |
| Base bottoms | 28½ × 23¼ | 4 | 1 long | Thin | 114 | 4 |
| Shelves | 28⅜ × 21 | 4 | 1 long | Thin | 113.5 | 4 |
| Wall sides | 30 × 11¼ | 6 | 1 long | Thin | 180 | 6 |
Thin band: (647.5 + 22 × 1) × 1.10 = 736.45 in ≈ 61.4 ft (18.7 m)
Notice that adding everything together gives about 182 ft, which might look like “one roll.” But these are two different bands, so you figure and buy them separately. The same goes for color and width: every color-thickness-width combination is its own line on the order.
Common mistakes
- Skipping back edges in wet areas: the sink base bottom gets banded on all four sides.
- Band narrower than the panel: nothing left to trim, and the core shows.
- Not deducting thick banding: doors grow 4 mm and no longer fit the reveals you designed.
- Ordering exactly what you need: with no allowance or waste, one bad start leaves you out of banding mid-job.
From cut list to shopping list
When banding is captured per side on every part, the math stops being a separate chore: in Zeder Studio, a design produces a shopping list with sheets, banding and hardware, and a quote carries banding as its own line with a waste factor. To pick the panel under the band, read melamine vs. MDF vs. plywood; to price the whole thing, see how to quote a kitchen. Any unfamiliar term is in the glossary.
Save this, optimize the cut list and quote it in Zeder Studio.
Frequently asked questions
What thickness of edge banding should I use on doors?
2 mm PVC is the usual choice for doors and drawer fronts because it takes knocks better. Hidden edges are fine with 0.45 mm, and box fronts with 0.45 or 1 mm.
What width of edge banding do I need for ¾ in melamine?
Usually 22 mm (about ⅞ in), slightly wider than the panel so you can trim it flush. Check which widths your supplier stocks.
How do I calculate how much edge banding I need?
Add up the length of every banded edge times the quantity of parts, add about 1 in per edge for trimming and a waste factor (10% is common), then divide by the roll length and round up.
Do I need to subtract edge banding from the cut size?
With 1 or 2 mm banding, yes, if your sizes are finished sizes: a part with 2 mm on both long edges gets cut 4 mm narrower. With 0.45 mm banding many shops skip it.
What’s the difference between PVC and ABS edge banding?
They look and machine almost the same; ABS is chlorine-free and usually costs a little more. Both work on melamine by hand or on an edgebander.
Keep reading
Edge banding calculator
Calculate how many meters of edge banding you need per part and edge, with trim allowance and waste, and how many rolls to buy.
Optimization settings
What each optimizer setting does: blade kerf, edge trim, saw or CNC mode, cutting stages, objective, part rotation, offcuts first and banding.
Melamine vs. MDF vs. plywood
Real differences between melamine, MDF, particleboard and plywood for cabinets: moisture, screw holding, finishes, relative cost and where each one fits.
How to quote kitchen cabinets
How to price a kitchen cabinet job: measure, build the cut list, cost sheets, edge banding, hardware and labor, then set your price. With a worked example.
Cabinetmaking glossary
What melamine, MDF, edge banding, kerf, grain, offcut, cut list, panel saw, cup hinge, 32 mm system, toe kick and other shop terms mean.
Cut better starting with your next job
Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.