Skip to content

How to read a cut diagram

What every number, arrow and hatched area on a sheet cut diagram means, and the order a sheet is actually cut in.
Type
Guide
Updated
Reading time
6 min
Sections
12
On this page (12)

A cut diagram is the plan for each sheet: which parts come out of it, where they go and in what order it is cut. Reading it properly prevents half the mistakes in the shop. This guide goes symbol by symbol on a real example sheet, runs the numbers to prove the layout actually works at the saw, and ends with what to check before you start the panel saw.

Sheet 1 of 3 · White melamine 16 mm · 2440 × 1830
Offcut 2440 × 1321560 × 7202560 × 7203560 × 7204560 × 7205900 × 5606900 × 5607600 × 56081200 × 40091200 × 400
Illustrative example · this sheet's yield: 87.7% · hatched = reusable offcut

The parts of a diagram at a glance

What you seeWhat it meansWhat to do
HeaderMaterial, thickness, sheet size and sheet numberCheck the sheet on the saw is that one
Numbered rectangleOne part from the cut listCut it and label it with that number
Length × widthThe part’s cut sizeCheck the legend for which is length
ArrowGrain directionDon’t rotate the part
Hatched areaOffcut or wasteKeep large offcuts, with their size
Gap between partsWhat the blade removes (kerf)Confirm the kerf entered is your real one

1. The header: material, size and sheet number

Each diagram starts with the material (for example, white 16 mm melamine), the sheet size and how many sheets the job needs (“Sheet 1 of 3”). Before cutting, check that the sheet on the saw is the one on the diagram.

In a Zeder Studio plan each sheet shows as Board 1 of 3, with arrows to step through them. When a job mixes materials, every board says which one it is: don’t cut the 3/4" stock from the 5/8" diagram.

2. The parts: number and dimensions

Each rectangle is a part. The number identifies it in the cut list and on its label. Dimensions read as length × width; in most optimizers length follows the grain, but check your diagram’s legend.

When a part is too small to print its size, the diagram shows only the number: look it up in the parts list. That’s why every part deserves a clear name in the cut list ("Upper side 1," not "Part 14").

3. The arrows: grain

An arrow inside a part shows grain direction. Those parts cannot be rotated when cutting, or the wood pattern would run sideways on the door or front.

In the example, part 7 has no arrow: it’s a hidden or solid-color part, so the optimizer was free to turn it. The more parts that can rotate, the better the sheet yields; kerf and grain covers when grain is worth respecting.

4. Hatched areas: offcuts and waste

Hatching marks leftover material. If an offcut is large, keep it with its size: the optimizer can use it on the next job. Very thin strips are waste.

The example sheet has two leftovers: 176 × 720 mm (about 6 15/16 × 28 3/8 in) to the right of the first strip, and a 2440 × 132 mm strip (about 96 × 5 3/16 in) along the bottom. The long strip makes toe kicks, cleats or narrow fillers; the 176 mm piece may too, depending on the job. In the app, offcuts worth keeping are saved with Save N offcuts and show up in the Offcuts tab with size, material and location (reading the plan and saving offcuts).

5. The gaps between parts: kerf

The gap between parts is what the saw blade removes. That is why two 900 mm parts don’t come out of a 1800 mm strip, and two 24" parts don’t come out of a 48" strip. Read more in kerf and grain, explained.

This example drawing leaves 6 mm (about 1/4") between parts. In your shop that number is your blade’s real kerf: if the diagram was built with a different value, the last parts in each strip come out short.

6. Cut order

Guillotine diagrams are cut in levels:

  1. Trim: clean the sheet’s factory edge.
  2. First cuts: edge-to-edge cuts that split the sheet into strips.
  3. Second cuts: each strip is cut into parts.
  4. Third cuts: where a part shares a strip with a narrower one, it is trimmed last.

Cutting stages

On a panel saw or sliding table saw, each level is another turn of the workpiece. In the optimization settings you can cap it with Cutting stages: 2 stages (strips) forces every part in a strip to share the same width, 3 stages allows the final trim, and Free lets the optimizer use as many levels as it needs. Fewer stages means faster, simpler cutting, at the price of some yield.

7. Yield

Part area divided by sheet area. Use it to compare layouts of the same job, not different jobs: a cut list with many small parts almost always yields more.

Worked example: checking the sheet in the drawing

The example sheet is 2440 × 1830 mm (8 × 6 ft) with nine parts in three strips. Let’s prove the layout fits and see how much it yields:

Strip 1 (720 high): 4 × 560 + 3 × 6 = 2258 mm ≤ 2440 ✓ → 176 mm left
Strip 2 (560 high): 900 + 900 + 600 + 2 × 6 = 2412 mm ≤ 2440 ✓
Strip 3 (400 high): 1200 + 1200 + 6 = 2406 mm ≤ 2440 ✓
Height: 720 + 560 + 400 + 3 × 6 = 1698 mm ≤ 1830 ✓ → 132 mm left

Part area: 4 × 403,200 + 2 × 504,000 + 336,000 + 2 × 480,000 = 3,916,800 mm²
Sheet area: 2440 × 1830 = 4,465,200 mm²
Yield: 3,916,800 ÷ 4,465,200 = 87.7% · Waste: 12.3%

That 12.3% includes the offcuts you keep, not just sawdust. Keep the 2440 × 132 strip and what actually goes in the dumpster is far less. That’s why the plan’s Reusable offcuts figure matters as much as yield.

Common mistakes reading a diagram

  • Mixing up length and width. If the legend says length × width and you cut it the other way, a grained part ends up sideways.
  • Cutting out of order. Cut a part before separating its strip and you lose your reference edge, and square goes with it.
  • Tossing offcuts without writing them down. An offcut with no size or location is a lost offcut.
  • Working from an old diagram. If the cut list changed, optimize again. The app warns you when the list changed since the last run.
  • Skipping the trim cut. Factory edges are rarely square; use one as your reference and every part inherits the error.

Before you cut, check

  • Material, thickness and the sheet’s real size.
  • The first strip, measured before you continue.
  • That parts with arrows follow the grain.
  • A label on every part as it leaves the saw.

From the diagram to the saw

With the plan ready, Zeder Studio lets you Print report (each board with its parts), Download PDF and print QR labels to stick on each part as it comes off the saw; labels, offcuts and CNC exports are on the Cut plan (labels, report and CNC files). To try it with your own sizes, use the free optimizer, and to bring waste down, follow these techniques. Before you order, also check the sheet sizes your supplier stocks.

Save this, optimize the cut list and quote it in Zeder Studio.

Frequently asked questions

What do the hatched areas on a cut diagram mean?

Leftover material. Large offcuts are kept with their size for another job; very thin strips are waste.

In what order is a sheet cut?

Trim first, then edge-to-edge cuts that split the sheet into strips, then each strip into parts, and finally trim cuts on parts that share a strip with a narrower one.

How is yield calculated?

Part area divided by sheet area. On the example 2440 × 1830 mm sheet it comes to 87.7%.

Why is there a gap between parts on the diagram?

That’s the kerf, the width the blade removes on every cut. Ignore it and the last parts in each strip come out short.

Cut better starting with your next job

Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.