Millimeters to fractional inches converter
Millimeters → inches
Result
- Nearest fraction
- 11/16"
- Decimal
- 0.7087"
- Difference
- -0.54 mm
Inches → millimeters
Accepts 23 7/8, 23-7/8, 7/8 or 23.875
Result
- Millimeters
- 606.43 mm
- Centimeters
- 60.64 cm
Save this, optimize the cut list and quote it in Zeder Studio.
On this page (6)
Metric hinges and slides, European sheet goods, a cut list from a shop in Mexico: sooner or later you have to convert. This converter rounds to the nearest fraction of an inch and tells you how far off the rounding is, so you can decide whether it matters.
How the calculation works
fraction = round(inches × denominator) ÷ denominator, reduced
difference = fraction in mm − original measurement
mm = inches × 25.4
Precision (1/8", 1/16", 1/32" or 1/64") is the denominator. A positive difference means the fraction is larger than your measurement. Going the other way, it accepts 23 7/8, 23-7/8, 7/8 or 23.875, with or without the inch mark.
Worked example
at 1/16: 0.7087 × 16 = 11.34 → 11/16" = 17.46 mm (−0.54 mm)
at 1/32: 0.7087 × 32 = 22.68 → 23/32" = 18.26 mm (+0.26 mm)
23 7/8" = 23.875 × 25.4 = 606.425 mm = 60.64 cm
That’s why 18 mm sheet stock is not 3/4" (19.05 mm): it’s closer to 23/32", which is about what "3/4" plywood actually measures.
Quick reference
| mm | To 1/16" | Difference | To 1/32" | Difference |
|---|---|---|---|---|
| 6 | 1/4" | +0.35 mm | 1/4" | +0.35 mm |
| 12 | 1/2" | +0.7 mm | 15/32" | −0.09 mm |
| 15 | 9/16" | −0.71 mm | 19/32" | +0.08 mm |
| 16 | 5/8" | −0.13 mm | 5/8" | −0.13 mm |
| 18 | 11/16" | −0.54 mm | 23/32" | +0.26 mm |
| 19 | 3/4" | +0.05 mm | 3/4" | +0.05 mm |
| 25 | 1" | +0.4 mm | 31/32" | −0.39 mm |
| 100 | 3 15/16" | +0.01 mm | 3 15/16" | +0.01 mm |
| 560 | 22 1/16" | +0.39 mm | 22 1/16" | +0.39 mm |
| 600 | 23 5/8" | +0.07 mm | 23 5/8" | +0.07 mm |
| 720 | 28 3/8" | +0.72 mm | 28 11/32" | −0.07 mm |
| 1220 | 48 1/16" | +0.79 mm | 48 1/32" | −0.01 mm |
| 2440 | 96 1/16" | −0.01 mm | 96 1/16" | −0.01 mm |
| Inches | mm |
|---|---|
| 1/4" | 6.35 |
| 1/2" | 12.7 |
| 23/32" | 18.26 |
| 3/4" | 19.05 |
| 12" | 304.8 |
| 24" | 609.6 |
| 30" | 762 |
| 34 1/2" | 876.3 |
| 36" | 914.4 |
| 48" | 1,219.2 |
| 96" | 2,438.4 |
When you’ll need it
The usual suspects in a US shop: European hinges and drawer slides spec’d in millimeters (35 mm cup holes, 32 mm system spacing), metric sheet goods sold as "4 × 8," imported hardware drawings and cut lists from metric shops. Going the other way, appliance openings like a 30" range (762 mm) or a 34 1/2" base cabinet height (876.3 mm) need to become millimeters when you work with a metric supplier. Convert once, write the result on the cut list and keep the whole job in one system.
Common mistakes
- Using 25 instead of 25.4. On a 96" sheet that’s off by more than 1 1/2 inches.
- Rounding each part, then adding. Ten sizes each rounded half a millimeter become 5 mm, almost 3/16". Convert the total, then divide.
- Trusting nominal thickness. "3/4"" plywood rarely measures 19.05 mm; measure the sheet before you set dadoes.
- Mixing systems in one job. Pick inches or millimeters for the whole cut list and convert only what comes from outside.
Tips
- For sheet goods, 1/32" is plenty; 1/64" is rarely something you can mark with a tape.
- In Zeder Studio each shop chooses metric (mm) or imperial (fractional inches), and the optimizer accepts fractions like 23 7/8 when you type or import parts.
- Standard cabinet sizes in both systems are in standard kitchen cabinet dimensions, and sheet sizes in standard sheet sizes.
- With the size converted, work out doors with the door size calculator.
Related
Sheet sizes: Mexico vs. US
Common melamine, MDF and plywood sheet sizes in Mexico, the US and Europe, and why 4 × 8 is not exactly 1220 × 2440 mm.
Standard kitchen cabinet dimensions
Typical heights, depths and widths for base, wall and tall cabinets in the US and Mexico, with a dimensioned diagram and how they turn into parts.
Cabinet door size
Work out overlay or inset door sizes, single or pairs, from the opening, overlay and gaps.
Kerf and grain, explained
What kerf (blade width) is, typical values on common saws, and when grain direction must be respected while optimizing cuts.
Cabinetmaking glossary
What melamine, MDF, edge banding, kerf, grain, offcut, cut list, panel saw, cup hinge, 32 mm system, toe kick and other shop terms mean.
Sheet calculator
Work out how many melamine, MDF or plywood sheets you need from your parts, edge trim and waste percentage.
Frequently asked questions
How many millimeters are in an inch?
Exactly 25.4 mm. Multiply inches by 25.4 to get millimeters, and divide to go back.
Is 18 mm the same as 3/4 inch?
No. 3/4" is 19.05 mm. 18 mm is closer to 23/32" (18.26 mm).
What fraction precision should I use?
For sheet goods, 1/16" or 1/32" is enough. The converter shows how many millimeters off each precision leaves you.
Cut better starting with your next job
Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.