Skip to content

Cabinetmaking and sheet goods glossary

55 shop terms explained briefly: sheet goods, edge banding, cutting, hardware, dimensions and pricing, with the Spanish names used in Mexico where they help.

#

32 mm systemSystem 32, European system
Frameless construction method where holes in the cabinet sides are spaced 32 mm apart, so hinges, slides and shelf pins go in without measuring each one. Standard kitchen cabinet dimensions
4×8 sheetFull sheet, 49 × 97
The standard sheet size: 4 × 8 feet, or 1220 × 2440 mm. Some brands sell other sizes, such as 49 × 97″ or 5 × 8 ft; check actual dimensions with your supplier. Sheet sizes: Mexico vs. US

A

ABS edge banding
Edge banding made of ABS plastic: chlorine-free, impact-resistant and trims cleanly. It usually costs a bit more than PVC. Edge banding types and how to calculate it

B

Back panelCabinet back
Rear panel of the cabinet, typically 1/8″ hardboard or thicker MDF or melamine. It sits in a groove or is nailed or screwed on, and keeps the box square. Melamine vs. MDF vs. plywood
Base cabinetLower cabinet, base
Floor-standing cabinet that sits under the countertop. Standard US boxes are 34-1/2″ tall and 24″ deep, putting the countertop at about 36″. Standard kitchen cabinet dimensions
Beam sawPanel sizing saw, horizontal panel saw
Industrial saw with a moving beam that cuts stacks of sheets with guillotine cuts, often programmed. It’s used in factories and high-volume panel shops. How to read a cut diagram

C

Cam lockMinifix, cam and dowel, cam fitting
Knock-down fastener with a cam and bolt: the bolt goes into one panel and the cam, in a hole typically 15 mm across, tightens it from the other. It lets cabinets be assembled and taken apart without damaging the board. Standard kitchen cabinet dimensions
CNC routerCNC, nesting router
Computer-controlled machine that cuts, drills and grooves panels with router bits from a program. It enables nesting and can drill hardware holes in the same pass. Labels, PDF and CNC files
Confirmat screwConfirmat, euro screw
Thick, coarse-thread screw made for particleboard and MDF, typically 7 × 50 mm. It goes into a stepped pilot hole and gives a strong, fast joint. Standard kitchen cabinet dimensions
CountertopCounter, worktop
The work surface on top of the base cabinets: granite, quartz, laminate or wood. It’s priced per linear or square foot depending on the material. Cabinet design
Cup hingeConcealed hinge, European hinge, 35 mm hinge
Concealed hinge set into a 35 mm hole bored in the door and screwed to a mounting plate on the cabinet side. It adjusts three ways and comes in full overlay, half overlay and inset versions. Cabinet door size
Cut listParts list, cutting list
The list of every part in a cabinet or project, with name, size, quantity, material, grain and banded edges. It’s the input for a cutting optimizer. Enter and import parts
Cutting diagramCutting layout, sheet layout, cutting plan
Drawing of each sheet showing where every part goes and the cut sequence. It’s what the operator takes to the saw. How to read a cut diagram
Cutting optimizerCut list optimizer, panel optimizer, nesting software
Software that lays out cut-list parts on sheets to use less material while respecting kerf, trim and grain. It outputs a cutting diagram for each sheet. Free cutting optimizer

D

DepositDown payment, upfront payment
Payment the customer makes when accepting a quote so the shop can buy material and get started; 50% is a common ask. The balance is due at milestones or on installation. How to quote kitchen cabinets
DowelWood dowel, dowel pin
Cylindrical wood pin, typically 8 mm in diameter, that aligns and reinforces panel joints. It’s used with glue or alongside cam locks. Standard kitchen cabinet dimensions
Drawer frontDrawer face
The visible face of the drawer, attached to the front of the drawer box and carrying the pull. It’s sized like a door, with the same reveals. Cabinet door size
Drawer slideDrawer runner, full-extension slide, undermount slide
Hardware that lets a drawer open. Ball-bearing side-mount slides are visible when open; undermount slides hide under the drawer and often include soft close. Standard kitchen cabinet dimensions

E

Edge bandingEdge tape, edgebanding, banding
Thin strip glued to sheet edges to cover the core and finish the part. It’s sold by the roll, in widths like 7/8″ (22 mm) and typical thicknesses of 0.45, 1 or 2 mm. Edge banding types and how to calculate it
Edge trimTrim cut, edge cleanup, sheet trim
A cleanup cut along the factory edges of a sheet, which can be dinged or out of square. A few millimeters per edge are set aside before parts are laid out. Optimization settings
EdgebanderEdge bander, edge banding machine
Machine that applies edge banding with hot-melt glue and trims it flush; automatic models also end-trim and profile. Small shops often use a manual edgebander or an iron-on approach. Edge banding types and how to calculate it

F

Fitted kitchenCustom kitchen, built-in kitchen
Custom kitchen built as one set of base cabinets, wall cabinets, tall units and countertop designed for the space. Kitchen cabinet makers
Full overlayOverlay door
Door that completely covers the front edge of the cabinet side. It’s the standard look for frameless cabinets. Cabinet door size

G

Gola profileHandleless profile, J-channel
Aluminum channel installed between fronts so doors and drawers open by finger grip, with no pulls. It’s typical of handleless, minimalist kitchens. Kitchen cabinet makers
Grain directionGrain, grain match
The direction of the pattern on woodgrain or textured sheets. Grained parts can’t be rotated during layout, since the pattern has to run the same way across doors and panels. Optimization settings
GrooveDado, back groove
Channel cut along a part to take the back panel or drawer bottom. It’s sized to the panel thickness and usually a few millimeters deep. Standard kitchen cabinet dimensions
Guillotine cutThrough cut, edge-to-edge cut
A straight cut that runs edge to edge and splits the panel in two. It’s the only kind a table saw or beam saw can make, so saw layouts are built from these cuts. How to read a cut diagram

H

Half overlayPartial overlay
Door that covers only half of the side panel’s edge, so two doors can share one center partition. Cabinet door size
HardboardMasonite, 1/8″ back panel
Thin, dense fiberboard, typically 1/8″ (3 mm), used for cabinet and drawer backs. It comes raw or with one melamine face. Melamine vs. MDF vs. plywood

I

InsetInset door, flush inset
Door that sits inside the cabinet opening, flush with the front. It takes more precision and even reveals. Cabinet door size

K

KerfSaw kerf, blade width
The width of material the blade removes on each cut. For panel blades it’s usually about 1/8″ to 3/16″ (3 to 4.5 mm); the optimizer leaves it between parts so sizes come out right. Kerf and grain, explained

L

LaborShop labor
The cost of the shop’s work: cutting, banding, assembly and installation. It’s quoted by the hour, per part, per cabinet or per linear foot. How to quote kitchen cabinets
Linear meterLinear foot, running meter
A length measure used to sell edge banding or to price countertops and cabinet runs per meter of wall. In the US the equivalent is pricing per linear foot. Edge banding calculator

M

MarginGross margin, profit margin
The share of the price that’s profit: price = cost ÷ (1 − %). A 30% margin on a $1,000 cost gives about $1,428.57, which is why the same % as markup and as margin doesn’t match. Markup vs. margin
MarkupCost-plus
Percentage added on top of cost to set the price: price = cost × (1 + %). A 30% markup on $1,000 gives $1,300. Markup vs. margin
MDFMedium-density fiberboard
Medium-density fiberboard: wood fibers pressed with resin into a smooth, uniform sheet. It machines and paints well, which makes it a go-to for painted or routed doors, and it’s sold raw or melamine-faced. Melamine vs. MDF vs. plywood
MelamineThermally fused laminate (TFL), melamine board
Particleboard or MDF faced on both sides with resin-impregnated paper, so it comes prefinished in white, solid colors or woodgrains. It’s a workhorse for closets and frameless cabinets; common thicknesses are 5/8″ and 3/4″ (16 and 18 mm). Melamine vs. MDF vs. plywood
Moisture-resistant boardMR board, MR MDF, green-core board
Particleboard or MDF made to resist moisture, usually recognizable by its green-tinted core. It’s used for sink bases and bathrooms; it handles humidity, not standing water. Melamine vs. MDF vs. plywood

N

NestingCNC nesting, nested-based manufacturing
Laying out parts on a sheet to be cut on a CNC router. Because the bit doesn’t need edge-to-edge cuts, parts can be packed more freely than on a saw. Optimization settings

O

OffcutRemnant, drop, cutoff
Leftover piece of sheet that’s still big enough for small parts. Logging offcuts with size and location keeps you from buying extra sheets. How to reduce melamine waste

P

ParticleboardChipboard, MDP, particle board
Panel made from wood particles bonded with resin. It’s cheaper and lighter than MDF and is the core of most melamine; its edges are rough and get covered with edge banding. Melamine vs. MDF vs. plywood
PlywoodPly, cabinet-grade plywood
Panel made of thin wood veneers glued with alternating grain. It holds screws and handles moisture better than particleboard, so it’s used for boxes, drawers and bathroom cabinets. Melamine vs. MDF vs. plywood
PullHandle, knob
Hardware for opening doors and drawers: bar, knob, edge profile or recessed. Its hole spacing belongs on the drilling plan. Cabinet design
PVC edge banding
Edge banding made of PVC plastic, widely available in many colors and finishes. It’s applied with hot-melt glue on an edgebander or by hand. Edge banding types and how to calculate it

S

Sales taxIVA (Mexico), VAT
Tax added to the sale price; in the US the rate and what’s taxable depend on the state and city. In Mexico the equivalent is IVA, at a 16% general rate. Quoting
Scoring bladeScorer, scoring saw
Small blade ahead of the main blade that scores the underside of the panel. It prevents chipping on melamine and other laminates. Kerf and grain, explained
ShelfAdjustable shelf, fixed shelf
Horizontal panel inside the cabinet; it can be fixed or adjustable on shelf pins set in 32 mm system holes. Standard kitchen cabinet dimensions
Side panelCabinet side, end panel, gable
Each vertical side of a cabinet box. It carries the holes for hinges, slides and shelf pins. Standard kitchen cabinet dimensions
Sliding table sawSlider, panel saw
Table saw with a sliding carriage for cutting full sheets square. It’s a common panel-cutting machine in small and mid-size cabinet shops. How to read a cut diagram
StretcherRail, top rail, nailer
Horizontal part that ties the sides together at the top or front and stiffens the box; on base cabinets it supports the countertop. Standard kitchen cabinet dimensions

T

Tall cabinetPantry cabinet, oven tower, utility cabinet
Full-height cabinet that runs from the floor to the top of the uppers or the ceiling; used as a pantry or to house an oven and microwave. Standard kitchen cabinet dimensions
Toe kickKick plate, plinth, toe space
Recessed strip at the bottom of base cabinets that hides the legs or base and leaves room for your feet. It’s usually about 4″ (10 cm) high. Standard kitchen cabinet dimensions

W

Wall cabinetUpper cabinet, upper
Upper cabinet hung on the wall above the countertop. It’s typically 12″ deep. Standard kitchen cabinet dimensions
Waste allowanceWaste factor, overage
Extra percentage added to material quantities to cover waste, mistakes and defects. In quotes it’s applied to sheets and banding so you don’t come up short. How to reduce melamine waste

Y

YieldMaterial yield, sheet utilization
The percentage of the sheet that ends up as usable parts; the rest is waste. It depends on part sizes, grain, kerf and trim. How to reduce melamine waste

Cut better starting with your next job

Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.