Cut: enter parts or import them from Excel
- Type
- Help center
- Updated
- Reading time
- 3 min
- Sections
- 6
On this page (6)
The cut list is the foundation: if one size or quantity is off, the layout is off too, no matter how good the optimizer is. Here’s how to enter parts by hand, paste your list from Excel or Google Sheets, and which columns the importer recognizes.
Start a cut list
Go to Cut and click New cut list.
Name it at the top (for example “Miller kitchen”). Leave it blank and it saves as “Untitled cut list.”
Check the Unit selector in the corner: mm, cm, in, or in (1/32) for fractional inches. It starts with your workshop’s units and you can switch anytime; it only changes how sizes are shown and entered.
The job has four sections: Parts, Materials, Settings and Import. A new cut list opens on Import, ready for you to paste.
The parts table
| # | Part | Qty | Length (in) | Width (in) | Sheet | Grain | Edge |
|---|---|---|---|---|---|---|---|
| 1 | Side | 2 | 30 | 23 1/4 | White melamine 3/4 | Any | top |
| 2 | Door | 2 | 29 7/8 | 15 7/16 | Walnut 3/4 | Lengthwise | 4 sides |
- Part: the name shown on the diagram and on labels.
- Qty: how many identical parts. The counter at the top adds up quantities, not rows.
- Length and Width: the part’s finished size.
- Sheet: which material it’s cut from; you add sheets in the Materials section.
- Grain: Any (free to rotate), Lengthwise (grain runs along the part’s length) or Widthwise.
- Edge: a small box with four bars, one per side (Top, Bottom, Left, Right). Click a bar to add or remove banding on that side. It uses the edge band thickness set under Materials.
Each row ends with Duplicate and Remove part; below the table is Add part. Sizes take decimals and, in inches, fractions.
Paste from Excel or Google Sheets
In your spreadsheet, select the table including the header row and copy it.
Under Import, paste it into the “Paste your list from Excel, Google Sheets or CSV” box. Have a file? Use Open CSV file (CSV, TSV or TXT).
Check the preview: “Preview: N rows, N pieces,” the detected columns and any warnings.
Pick Add to list to append to what you have, or Replace list to start over. You land back on the Parts table.
The header doesn’t have to be the first row: if your template has a title and instructions on top, the importer finds the header row further down. Materials in the file are matched by name, first in the job and then in your catalog; if there’s no match, a quick sheet with that name is created so you can set its size.
Recognized headers
| Field | Accepted headers (examples) |
|---|---|
| Name | Name, Part, Description, Label, Nombre, Pieza |
| Length | Length, Height, Largo, Alto |
| Width | Width, Ancho, Fondo |
| Quantity | Qty, Quantity, Count, Pcs, Cantidad, Piezas |
| Material | Material, Board, Color, Tablero |
| Thickness | Thickness, Thk, Espesor, Grosor |
| Grain | Grain, Grain direction, Veta, Sentido |
| Edge | Edge, Edgeband, Banding, Canto; also one column per side (Edge Top, Edge Left…) |
| Cabinet | Cabinet, Assembly, Módulo, Mueble |
Worth knowing:
- Decimal commas (720,5) and fractional inches (23 1/4) are both accepted.
- A unit in the header wins over the one on screen: “Length (in)” is read in inches even if the job is in mm.
- A blank quantity counts as 1; a 0 turns that row off. If a quantity can’t be read, it comes in as 1 with a warning.
- Grain: “yes,” “1” or “length” means lengthwise; “2” or “width” means widthwise; “no” or “0” means any.
- A single Edge column with “yes,” “1” or “X” bands all four sides; “0” or “no” means no banding.
- No thickness column? 18 mm (about 3/4″) is assumed.
Free plan limit
On the Free plan each optimization takes up to 50 parts, counting quantities (2 sides = 2 parts). Go over and you’ll see “Your plan allows 50 parts per optimization; this list has N.” with an Upgrade button. Paid plans have no limit. To try it without an account, there’s the free optimizer, also up to 50 parts.
Parts from a design
If you work in Design, don’t enter parts twice: from the design, send it to Cut. A revision is created and a new cut list opens with “Parts loaded from the design (revision N).” Check sizes and sheets before optimizing. More in Send a design to Cut.
Save this, optimize the cut list and quote it in Zeder Studio.
Frequently asked questions
Do my columns need to be in a specific order?
Not if your list has headers: they’re recognized by name in English or Spanish. Only without headers are columns read in order: name, length, width, qty, thickness, material.
Does the 50-part limit count rows or quantities?
Quantities. A row with a quantity of 4 counts as 4 parts.
Keep reading
Optimization settings
What each optimizer setting does: blade kerf, edge trim, saw or CNC mode, cutting stages, objective, part rotation, offcuts first and banding.
Results and offcuts
How to read the plan's metrics (sheets, yield, cuts), page through each sheet, handle parts that don't fit and save or use offcuts.
Materials and catalog
Add sheets, edge banding and hardware with sizes, kerf, grain and cost; import the Mexico starter catalog or your own CSV and assign suppliers.
Free cutting optimizer
Enter your parts and get a cut diagram for your melamine or MDF sheets for free, in the browser. For jobs of up to 50 parts.
Standard kitchen cabinet dimensions
Typical heights, depths and widths for base, wall and tall cabinets in the US and Mexico, with a dimensioned diagram and how they turn into parts.
Cut better starting with your next job
Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.