Optimization settings: kerf, trim, grain, stages
- Type
- Help center
- Updated
- Reading time
- 3 min
- Sections
- 5
On this page (5)
The optimizer only knows what you tell it. Each cut list’s Materials and Settings sections tell it which sheets you have, how much your blade eats and how your shop cuts. With the right values, what you see on screen is what comes off the panel saw.
Materials in the job
Every part is cut from a sheet added to the job. A new cut list starts with a sheet from your catalog if you have one. To add more, there are two ways:
- From catalog…: pick a sheet from Materials. It brings its sheet size, thickness, kerf, trim, grain and cost.
- Quick sheet (no catalog): for a test or a material you haven’t set up. It starts at 2440 × 1220 mm (about 96 × 48″), 18 mm thick, 4 mm kerf and no trim; rename it right there.
On each sheet you can adjust Sheet size, Thickness, Kerf, Trim and Grained. “Used by N parts” shows how many parts use it; while it has parts, it can’t be removed. Below are Default edge band (an edge band from your catalog) and Edge band thickness, which is applied when you mark sides in the parts table.
Kerf and trim
Under Settings, Kerf and Trim per edge start checked as From material: each sheet uses its own value. Uncheck it to type one value for every sheet in this job, handy if you’re running a different blade today. We cover it in depth in what kerf is.
Mode and cutting stages
- Saw (guillotine): every cut runs edge to edge, the way a sliding table saw or beam saw works. This is the default.
- CNC (nesting): places parts without the guillotine rule, for a CNC router.
Cutting stages only applies in saw mode: Free doesn’t limit direction changes; 2 stages (strips) rips strips first and then crosscuts them to size; 3 stages allows one more cut inside each strip. Fewer stages means an easier sequence to follow, sometimes with a bit more waste.
Priority, rotation and search
| Setting | Options and what it does |
|---|---|
| Prioritize | Least waste (default), Fewest boards, Fewest cuts, Reusable offcuts, Lowest cost (needs costs in the catalog) or Repeated patterns. |
| Allow rotating parts without grain | On by default. Parts with Grain set to “Any” can turn 90° to fit better. |
| Search | Fast, Normal (default) or Extensive. More search tries more layouts and takes longer. |
| Use offcuts first | Uses your saved offcuts of the same material before opening new sheets, and shows how many are available. Requires the Cut plan. |
| Deduct edge band from cut size | Subtracts the band thickness on banded sides so the part finishes at the size you entered. |
Starting values for a panel saw shop
These are suggestions for melamine and MDF cut on a sliding table saw, not rules. Adjust them to your blade and your sheets.
| Setting | Suggestion | Why |
|---|---|---|
| Kerf | Your blade’s actual kerf, often around 1/8″ to 3/16″ (3–4.5 mm) | Check the blade spec or measure a test cut. |
| Trim | About 3/8″ (10 mm) per edge | Factory edges arrive dinged or out of square. |
| Mode | Saw (guillotine) | That’s how a panel saw cuts. |
| Stages | 3 stages | An easy sequence without hurting yield much. |
| Prioritize | Least waste | Switch to Fewest cuts on rush jobs. |
| Search | Normal | Extensive for big jobs or pricey sheets. |
| Deduct edge band | On if you use thick banding | With 1 or 2 mm banding the difference shows at assembly. |
Once that’s set, move on to reading the cutting plan. For the difference between guillotine cuts and nesting, see the cutting diagram guide.
Save this, optimize the cut list and quote it in Zeder Studio.
Frequently asked questions
What happens if I leave kerf on “From material”?
Each sheet uses the kerf stored in the catalog; if there isn’t one, 4 mm is used.
When should I use CNC (nesting) mode?
When you cut on a CNC router. On a panel saw or beam saw use Saw (guillotine), because every cut has to run all the way across.
Keep reading
Enter and import parts
How to fill the parts table, paste a list from Excel or Google Sheets, open a CSV and which columns are recognized (length, width, qty, grain, banding).
Results and offcuts
How to read the plan's metrics (sheets, yield, cuts), page through each sheet, handle parts that don't fit and save or use offcuts.
Kerf and grain, explained
What kerf (blade width) is, typical values on common saws, and when grain direction must be respected while optimizing cuts.
How to reduce melamine waste
Proven ways to get more out of every sheet: grain, design dimensions, offcuts, kerf, cut order and how to measure your real waste.
How to read a cut diagram
What every number, arrow and hatched area on a sheet cut diagram means, and the order a sheet is actually cut in.
Cut better starting with your next job
Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.