Standard sheet sizes: Mexico vs. US vs. Europe
- Type
- Guide
- Updated
- Reading time
- 5 min
- Sections
- 7
On this page (7)
Sheet size decides how many parts fit and how much is left over. These are common sizes by region; exact sizes and thicknesses vary by manufacturer, so always measure the sheet you buy. Below you’ll see why a millimeter matters, how thickness shifts the whole cut list, and how to decide which size to buy, with a worked example.
Common sizes by region
| Region | Common sizes | Notes |
|---|---|---|
| Mexico | 2440 × 1830 mm (8 × 6 ft) 2440 × 1220 mm (8 × 4 ft) | 2440 × 1830 is the most common melamine size; 2440 × 1220 is typical for MDF and plywood. |
| United States | 48 × 96 in (4 × 8 ft) 49 × 97 in | 4 × 8 is exactly 1219.2 × 2438.4 mm. Melamine is often sold at 49 × 97 in to leave room for trimming. |
| Europe | 2800 × 2070 mm | Larger sheets, common for European melamine-faced boards. |
If you buy sheet goods from a metric supplier, "4 × 8" may really mean 1220 × 2440 mm, which is a hair bigger than a true 48 × 96. Ask for the size in the unit the sheet was made in; the optimizer needs the exact number.
4 × 8 is not 1220 × 2440
A 4 × 8 ft sheet measures 1219.2 × 2438.4 mm. If you set the optimizer to 1220 × 2440 and your sheet is truly 4 × 8, every strip comes up almost a millimeter short. Use the real size.
The difference is 0.8 mm across the width and 1.6 mm along the length, about 1/32" and 1/16". It sounds like nothing, but when a layout uses the full sheet with no leftover, the last part in each strip pays for it. To convert without mistakes, use the mm to inches converter.
Nominal vs. actual thickness
- In Mexico, melamine is sold in thicknesses like 15–16 mm and 18–19 mm depending on the manufacturer.
- In the US, “3/4” plywood usually measures less (around 23/32", about 18 mm).
- Backs are usually 3 or 6 mm.
Thickness changes shelf, back and drawer sizes: a 15 mm side instead of 18 mm shifts every interior part. To convert, use the mm to inches converter.
Example: the same cabinet in two thicknesses
Sides at a true 3/4": opening = 24 − 2 × 3/4 = 22 1/2 in
Sides at 23/32": opening = 24 − 2 × 23/32 = 22 9/16 in
Difference: 1/16" on bottom, top, shelves, drawer bottoms and doors
Build the cut list for 3/4" and get 23/32" stock, and every interior part is 1/16" short, or the box grows 1/16". Measure the delivered sheet with calipers before you cut, and if it changed, update the material before you optimize.
Which size should you buy?
It depends on your cut list. Tall parts like 2400 mm closet sides need 2440-long sheets; jobs with many mid-size parts may yield better on 2440 × 1830. To find out, compare the same cut list on both sizes with the sheet calculator or the optimizer.
Worked example: 48 × 96 vs. 49 × 97
Say you trim 3/8" off every edge and need two 24" rips across the width, a common ask for base cabinet parts and countertop substrates:
Two 24" rips + 1/8" kerf = 48 1/8 in > 47 1/4 ✗ → only one rip
49 × 97 trimmed: 49 − 2 × 3/8 = 48 1/4 in usable width
Two 24" rips + 1/8" kerf = 48 1/8 in ≤ 48 1/4 ✓ → both rips
That’s the point of the oversize sheet: after trimming you still have a full 48 × 96 to work with. For a different cut list the regular sheet may be the better buy, which is why you compare with your real parts, not a rule of thumb.
The same logic applies by area. With the sheet calculator’s sample parts, 10 mm trim and 15% waste:
| Sheet | Usable area | Math | Sheets |
|---|---|---|---|
| 96 × 48 in (2438 × 1219 mm) | 2.90 m² (31.2 sq ft) | 6.33 ÷ 2.90 = 2.18 | 3 |
| 2440 × 1830 mm (8 × 6 ft) | 4.38 m² (47.1 sq ft) | 6.33 ÷ 4.38 = 1.44 | 2 |
Compare price per square foot, not per sheet: divide each sheet’s price by its area and multiply by what the job actually uses.
What about the 2800 × 2070 mm European sheet?
Bigger isn’t always better. With the same parts, a 2800 × 2070 mm sheet (about 110 × 81 in) has 5.70 m² usable and the math gives 6.33 ÷ 5.70 = 1.11, so 2 sheets: you buy 11.59 m² of material against 8.93 m² with the 8 × 6 option. Big sheets pay off when you have parts longer than 96", like floor-to-ceiling closet or pantry sides, or jobs so large that the last sheet’s leftover hardly matters. Factor in handling too: a sheet that size is harder to move and to cut on a small sliding table saw.
Enter the right size in your catalog
In Zeder Studio every sheet in the catalog stores length, width, thickness, grain, kerf and trim. Enter them right once and every job inherits them. Catalogs can be imported from CSV with headers like length_in and width_in for imperial shops (how the catalog works).
Common mistakes
- Entering the nominal size. "4 × 8" can be 1220 × 2440 mm or 1219.2 × 2438.4 depending on where it was made.
- Assuming thickness. "3/4"" covers sheets from about 18 to 19 mm; measure before you cut dadoes.
- Comparing price per sheet only. A cheaper sheet can cost more per square foot, or per job.
- Forgetting trim when comparing. Both sizes lose their edges; compare usable area, not nominal.
- Mixing two sizes without telling the optimizer. If you stock both, enter them as two sizes of the same material.
Keep going
For a whole kitchen, see how many sheets a kitchen needs. Still choosing material? Compare melamine vs. MDF vs. plywood. The cabinet sizes you’ll be cutting are in standard kitchen cabinet dimensions, and how the blade affects each strip is in kerf and grain.
Save this, optimize the cut list and quote it in Zeder Studio.
Frequently asked questions
What size is a sheet of plywood or melamine?
In the US the standard is 48 × 96 in (4 × 8 ft); melamine is also sold at 49 × 97 in to allow for trimming. In Mexico 2440 × 1830 mm is the most common melamine size.
Is a 4 × 8 sheet 1220 × 2440 mm?
Not exactly: 4 × 8 ft is 1219.2 × 2438.4 mm. The 0.8 and 1.6 mm difference is enough to make the last part in a strip come out short.
How thick is 3/4 plywood really?
Usually less than 3/4 in, often around 23/32 in (about 18 mm). Measure the sheet before setting dadoes or joinery.
Why buy 49 × 97 sheets?
So you can trim the factory edges and still have a full 48 × 96 to work with, which matters when a layout needs the whole width.
Keep reading
Sheet calculator
Work out how many melamine, MDF or plywood sheets you need from your parts, edge trim and waste percentage.
mm to inches
Convert millimeters to fractional inches (1/16, 1/32, 1/64) and inches like 23 7/8 back to millimeters. Built for the shop.
Melamine vs. MDF vs. plywood
Real differences between melamine, MDF, particleboard and plywood for cabinets: moisture, screw holding, finishes, relative cost and where each one fits.
How many sheets a kitchen needs
How to work out melamine and back panel sheets for a kitchen: parts per cabinet, a 3-meter worked example, realistic waste and common mistakes.
Kerf and grain, explained
What kerf (blade width) is, typical values on common saws, and when grain direction must be respected while optimizing cuts.
Materials and catalog
Add sheets, edge banding and hardware with sizes, kerf, grain and cost; import the Mexico starter catalog or your own CSV and assign suppliers.
Cut better starting with your next job
Create an account and use the full Workshop plan for 14 days. No card; afterwards you drop to the Free plan, not a lockout.